E31

CC CV Buck Converter DC-DC 5.3V-32V to 1.2V-32V 12A 160W Step Down Power Supply Module Voltage Regulator LCD Transformer /w Case

Description:

This module is a DC adjustable constant voltage constant current step down power supply module with LCD display. HD display input voltage and output voltage, current, power and display status. Adjustable stable output voltage and current. Set output current to meet the demand. It can be used as ordinary buck power supply module, charger and LED constant current driver. Simple and efficient, practical.

DC DC Boost Converter Module working frequency 1.2MHZ.

Up to 95% Efficiency (usually is 84%-92%)

Quiescent Current (PFM) : 100uA.
Quiescent Current (PWM): 1.6mA

Automatic Pulse Frequency Modulation Mode at Light Loads

Under voltage lockout,Current limiting,Thermal overload protection

Operating temperature range : -40~+85 Degrees Celsius

Storage temperature range : -65~+150 Degrees Celsius

Size : 31mm x 11.5mm x 4.5mm
Weight :  2g


Output 6V :

Features:

1. Adopt new imported chips.

2. The maximum output current is 3A, running 2.1A for a long time, and the surplus is sufficient. 3A runs for about 20 seconds and the chip enters the overheat protection and restarts. It can work at 3A current by cooling and cooling the chip.

3. Using a new design scheme, the circuit design does not need electrolytic capacitors and tantalum capacitors (electrolytic capacitors have short life, tantalum capacitors are in danger of explosion). Three large-size solid-state ceramic capacitors (MCC) are used in high-end circuits.

This is a 20W adjustable DC-DC buck converter module with digital display. It is based on LM2596 3A step-down voltage regulator and supports an input of 4~40V DC with an accuracy of ± 0.05V.

• Size: 20 * 20 * 5mm
• Input voltage: 4.75V-24V
• Output voltage: 0.92V-15V
• Output Current: 2A (maximum)
• Voltage Regulation: ± 2.5%
• Load Regulation: ± 0.5%
• Load Regulation: ± 0.5%
• Output ripple: 30mV (max)
• Switching frequency: 1.2MHz
• Operating Temperature: -40℃ to +85 ℃
• Conversion efficiency: 95% (the highest)
• Module Properties: non-isolated step-down (BUCK)
• Rectification: non-synchronous rectification

•   Input voltage range: 5V-60V (rated Suggestions below 50V reliable) 
•   Output voltage range: 1.25V-26V 
•   Output current: 3A(MAX)-need to add heat sink 
•   Continuous working current: 1.2A (total power output within 20W) 
•   Conversion efficiency: Up to 92% (output voltage higher, the higher the efficiency) 
•   Switching Frequency: 150KHz 
•   Rectifier: Non-Synchronous Rectification 
•   Module Properties: Non-isolated step-down module (buck) 
•   Short circuit protection: current limiting, since the recovery 

This module is a non-isolated step-up (boost) voltage converter featuring adjustable output voltage and high efficiency.

Specifications

Super compact and capable, this DC-DC buck converter can knock down a voltage from 23V to as low as 1V with up to 95% efficiency.

Description

One of our engineers came by and showed off one of his latest finds, the Mini-360 DC-DC buck converter. He needed a small and efficient voltage-reduction circuit for a remote application, and this unit tests out quite well. Inexpensive enough to be worth having a few in the toolbox for emergency voltage regulation!

Specifications:

PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you'll be able to keep your power-hungry project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects.

The MCP23017 is a 16-bit, general purpose parallel I/O port expander for I2C bus applications. The 16-bit I/O port functionally consists of two 8-bit ports (PORTA and PORTB). The MCP23017 can be configured to operate in 8-bit or 16-bit modes.